用途：用于橡胶出片冷却把水吹干。
特点: 本机采用强力风机根据风刀角度把胶片吹干。
主要技术参数 Technical Parameters | |
型号 Model | LJ-1200 |
外型尺寸Appearance Size: L*W*H(mm) | 1200*950*1430 |
工作宽度Working Width(mm) | 600 |
风刀功率Power (KW) | 5.5 |
输送功率Power (KW) | 0.75 |
重量Weight(kg) | 300 |
使用说明
公共设备电力：电压380V,50Hz。
主电源线：4平 四芯线
1、 机械运转中手切勿接触滚轮。
2、 橡胶片应该保持平整进料，防止卡料。
3、 进料胶片厚薄要一致且要平整进入胶辊，太簿的胶片进胶棍必需折成双层，喷水量要够多，弹簧（进料胶棍）不要调整过紧，工人的操作速度快，以免卷料。
4、 以上操作失误，如有卷料，清理时，刀片一定不要损伤胶辊。
5、 后面出料胶辊进料时，簿料必需折成双层稍微一点拉力。不致于卷料，仍有存大阻料，查弹簧是否调整不当，查胶辊是否卡住，上面胶辊和下面胶辊是否紧贴，轴承是否没换油卡死，链条是否过松等。6、 压水不干，炼胶机上要装齐边刀，减少碎料，平整一致，调整胶辊弹簧，注意弹簧不要调死，以免损坏电机。
7、 胶片如两边跑动，请调整胶辊两端弹簧压力一致。
8、 机台工作时，手一定不要伸进里面，如有问题，一定要停机解决。
9、 滚轮工作时旋转不正常，请检查链条松紧情况，齿轮是否损坏。
10、 发现电机有异声，要停机检查，链条皮带松动要及时调整，螺丝松动要及时紧固。
11、 如风刀出风量小，查看过滤网是否灰尘过多堵塞，清洗过滤网。
Rubber water cooling machine:
Purpose: Used for rubber sheet cooling to dry the water.
Specialty: The machine USES a strong fan to dry the film according to the Angle of the blade.
主要技术参数 Technical Parameters | |
型号 Model | LJ-1200 |
外型尺寸Appearance Size: L*W*H(mm) | 1200*950*1430 |
工作宽度Working Width(mm) | 600 |
风刀功率Power (KW) | 5.5 |
输送功率Power (KW) | 0.75 |
重量Weight(kg) | 300 |
INSTRUCTIONS:
Public equipment：Power: 380V,50Hz.
Host power line: 4mm² four-core
1. Do not touch the cutter die and roller during the operation of the machine.
2. Rubber sheet should be kept flat to prevent material from sticking.
3. The thickness of feeding rubber slices must be consistent and the rubber slices should enter in the same level. Too thin rubber slices should enter in a way of double-decker. Water them with enough volume; do not adjust the spring too tight. The operating speed must be fast enough to avoid material rolling.
4. If above operational errors occur and material rolled, don’t let the blade operate the rubber roller when cleaning up.
5. When the triple-rubber-roller is feeding material, thin one must be folded into double-decker. If there still exist non-smoothly feeding, check whether the spring is adjusted properly; or check whether the rubber roller is blocked;
check whether the upper rubber roller is stuck with the lower one; or check whether the bearing roller is blocked for without oil replacing ;or check whether the chain is too loose, etc .
6. Pressurized water quit ,the knives should be installed in a level to the rubber making machine . Reduce rubber oddments and make rubber in a level and in the same thickness. Do adjust the spring, but not too tight to avoid damaging the MORTOR.
7. Rubber out of the sheet partial movement, please adjust the cots at both ends of the spring pressure consistent.
8. Do stop the machine when there is problem. Do not put hands in when the machine is still working.
9. The roller does not rotate properly when working. Please check the tightness of the chain and whether the gear is damaged.
10. Any unusual voice, stop and check. Adjust chains and screws if they are loose.
11. If the air output of the air knife is small, check whether the filter is clogged with too much dust and clean the filter.
